收藏本站
NXP Semiconductors
PCA9633
4-bit Fm+ I 2 C-bus LED driver
7.1.2 LED All Call I 2 C-bus address
? Default power-up value (ALLCALLADR register): E0h or 1110 000X
? Programmable through I 2 C-bus (volatile programming)
? At power-up, LED All Call I 2 C-bus address is enabled. PCA9633 sends an ACK when
E0h (R/W = 0) or E1h (R/W = 1) is sent by the master.
See Section 7.3.8 “LED All Call I 2 C-bus address, ALLCALLADR” for more detail.
Remark: The default LED All Call I 2 C-bus address (E0h or 1110 000X) must not be used
as a regular I 2 C-bus slave address since this address is enabled at power-up. All the
PCA9633s on the I 2 C-bus will acknowledge the address if sent by the I 2 C-bus master.
7.1.3 LED Sub Call I 2 C-bus addresses
? 3 different I 2 C-bus addresses can be used
? Default power-up values:
– SUBADR1 register: E2h or 1110 001X
– SUBADR2 register: E4h or 1110 010X
– SUBADR3 register: E8h or 1110 100X
? Programmable through I 2 C-bus (volatile programming)
? At power-up, Sub Call I 2 C-bus addresses are disabled. PCA9633 does not send an
ACK when E2h (R/W = 0) or E3h (R/W = 1), E4h (R/W = 0) or E5h (R/W = 1), or
E8h (R/W = 0) or E9h (R/W = 1) is sent by the master.
See Section 7.3.7 “I 2 C-bus subaddress 1 to 3, SUBADRx” for more detail.
Remark: The default LED Sub Call I 2 C-bus addresses may be used as regular I 2 C-bus
slave addresses as long as they are disabled.
7.1.4 Software Reset I 2 C-bus address
The address shown in Figure 9 is used when a reset of the PCA9633 needs to be
performed by the master. The Software Reset address (SWRST Call) must be used with
R/W = 0. If R/W = 1, the PCA9633 does not acknowledge the SWRST. See Section 7.6
“Software Reset” for more detail.
R/W
0
0
0
0
0
1
1
0
002aab416
Fig 9.
Software Reset address
Remark: The Software Reset I 2 C-bus address is a reserved address and cannot be used
as a regular I 2 C-bus slave address (16-pin version) or as an LED All Call or LED Sub Call
address.
PCA9633_5
? NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 25 July 2008
9 of 43
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
PCA9634D,118 IC LED DRIVER RGBA 20-SOIC
PCA9635PW/S911,118 IC LED DRIVER RGBA 28-TSSOP
PCA9685PW,118 IC LED DRIVER RGBA 28-TSSOP
PCA9922PW,118 IC LED DRIVER LINEAR 16-TSSOP
PCA9955TW,118 IC LED DRVR CONST CURR
PCF85102C-2P/03,11 IC EEPROM 2KBIT 100KHZ 8DIP
PCF85103C-2T/00,11 IC EEPROM 2KBIT 100KHZ 8SOIC
PCF8570T/F5,512 IC SRAM 2KBIT 100KHZ 8SOIC
相关代理商/技术参数
PCA9633BS-T 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16 功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16,112 功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16,118 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633DEMO 功能描述:开发板和工具包 - 8051 Brd Philips PCA9633 RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:
PCA9633DP1,118 功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633DP1,118-CUT TAPE 制造商:NXP 功能描述:PCA9633 Series 25 mA 5.5 V 1 MHz SMT 8-bit I2C-Bus LED Driver - TSSOP-8
PCA9633DP2,118 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N